1 ? fn7382.2 caution: these devices are sensitive to electrostatic discharge; follow proper ic handling procedures. 1-888-intersil or 321-724-7143 | intersil (and design) is a registered trademark of intersil americas inc. copyright ? intersil americas inc. 2004. all rights reserved. elantec is a registered trademark of elantec semiconductor, inc. all other trademarks mentioned are the property of their respective owners. preliminary el5132, EL5133 670mhz low noise amplifiers the el5132 and EL5133 are ultra-low voltage noise, high speed voltage feedback amplifiers that are ideal for applications requiring low voltage noise, including communications and imaging. these devices offer extremely low power consumption for exceptional noise performance. stable at gains as low as 10, these devices offer 120ma of drive performance. not only do these devices find perfect application in high gain applications, they maintain their performance down to lower gain settings. these amplifiers are available in small package options (sot-23) as well as the industry-standard so packages. all parts are specified for operation over the -40c to +85c temperature range. features 670mhz -3db bandwidth ultra low noise 0.9nv/ hz 1000v/s slew rate low supply current = 12ma single supplies from 5v to 12v dual supplies from 2.5v to 5v fast disable on the el5132 low cost applications imaging instrumentation communications devices pinouts el5132 (8-pin so) top view EL5133 (5-pin sot-23) top view ordering information part number package tape & reel pkg. dwg. # el5132is 8-pin so - mdp0027 el5132is-t7 8-pin so 7? mdp0027 el5132is-t13 8-pin so 13? mdp0027 EL5133iw-t7 5-pin sot-23 7? (3k pcs) mdp0038 EL5133iw-t7a 5-pin sot-23 7? (250 pcs) mdp0038 1 2 3 4 8 7 6 5 - + nc in- in+ vs- ce vs+ out nc 1 2 3 5 4 - + out vs- in+ vs+ in- data sheet april 5, 2004
2 absolute maximum ratings (t a = 25c) supply voltage from v s + to v s - . . . . . . . . . . . . . . . . . . . . . . . 13.2v i in -, i in +, ce . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5ma continuous output current . . . . . . . . . . . . . . . . . . . . . . . . . . 150ma power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see curves storage temperature . . . . . . . . . . . . . . . . . . . . . . . . -65c to +125c ambient operating temperature . . . . . . . . . . . . . . . . -40c to +85c operating junction temperature . . . . . . . . . . . . . . . . . . . . . . +125c caution: stresses above those listed in ?absolute maximum ratings? may cause permanent damage to the device. this is a stress o nly rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. important note: all parameters having min/max specifications are guaranteed. typical values are for information purposes only. u nless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: t j = t c = t a electrical specifications v s + = +5v, v s - = -5v, r l = 150 ? , r f = 900 ? , r g = 100 ? , t a = 25c, unless otherwise specified. parameter description conditions min typ max unit v os offset voltage -1 0.5 1 mv t c v os offset voltage te mperature coeffici ent measured from t min to t max 0.8 v/c ib input bias current v in = 0v 8 12 20 a i os input offset current v in = 0v -1250 400 +1250 na t c i os input bias current temperature coefficient measured from t min to t max 3na/c psrr power supply rejection ratio v s + = 4.75v to 5.25v 75 87 db cmrr common mode rejection ratio v in = 3.0 v 80 100 db cmir common mode input range guaranteed by cmrr test 3 3.3 v r in input resistance common mode 2 5 m ? c in input capacitance 2pf i s supply current 9.2 11 13 ma avol open loop gain v out = 2.5v, r l = 1k ? to gnd 5 8.5 kv/v v o output voltage swing r f = 900 ? , r g = 100 ?, r l = 150 ? 3.1 3.5 v i sc short circuit current r l = 10 ? 70 140 ma bw -3db bandwidth a v = +10, r l = 1k ? 670 mhz bw 0.1db bandwidth a v = +10, r l = 1k ? 90 mhz gbwp gain bandwidth product 3000 mhz pm phase margin r l = 1k ? , c l = 6pf 55 sr slew rate r l = 100 ? , v out = 2.5v 700 1000 v/s t r , t f rise time, fall time 0.1v step tbd ns os overshoot 0.1v step tbd % t pd propagation delay 0.1v step tbd ns t s 0.01% settling time 6.6 ns dg differential gain a v = +2, r f = 1k ? 0.01 % dp differential phase a v = +2, r f = 1k ? 0.01 e n input noise voltage f = 10khz 0.9 nv/ hz i n input noise current f = 10khz 4.9 pa/ hz el5132, EL5133
3 all intersil u.s. products are manufactured, asse mbled and tested utilizing iso9000 quality systems. intersil corporation?s quality certifications can be viewed at www.intersil.com/design/quality intersil products are sold by description only. intersil corporation reserves the right to make changes in circuit design, soft ware and/or specifications at any time without notice. accordingly, the reader is cautioned to verify that data sheets are current before placing orders. information furnishe d by intersil is believed to be accurate and reliable. however, no responsibility is assumed by intersil or its subsidiaries for its use; nor for any infringements of paten ts or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of intersil or its subsidiari es. for information regarding intersil corporation and its products, see www.intersil.com el5132, EL5133
|
